25W CC 350mA to 700mA PUSH and DALI2 compact led driver with 5 years warranty
1. Description:
1) Built-in DALI2 protocol, no flicker in full dimming range;
2) Primary Push dimming function; Push dimming has a state memory function;
3) Short circuit / over temperature / over voltage protection; reduce output current after over temperature;
4) Standby power consumption ≤ 0.5W;
5) 5-year warranty.
2. Specifications
| Input | Operating Voltage | 198-264VAC 50Hz /60Hz |
| Rated Input Voltage | 220-240VAC 50Hz /60Hz |
| DC Input Voltage range | 200-240VDC |
| Input Cuttent | 0.15A Max. |
| Input Inrush Current | <15A (Half current pulse width 100US) @230VAC |
| Power Factor | ≥ 0.95 (@230Vac,100% load) |
| Total harmonic distortion | Typical: 15% (@230Vac, 100% load) |
| Stand-by Power | ≤0.5W (@230Vac) |
| Efficiency | 86%Max (@230Vac,100% load) |
| Wiring Method | Push terminal, wire cross section:0.75-1.0mm2 |
| Automatic circuit breaker (Calculate current in the wire) | type | B10 | B13 | B16 | B20 | B25 | / |
| Number | 25 | 35 | 45 | 50 | 65 | / |
| type | C10 | C13 | C16 | C20 | C25 | C32 |
| Number | 55 | 65 | 75 | 110 | 130 | 160 |
| Output | Operating mode | Constant Current |
| Load type | LED |
| Ripple requirement (Flickering or flicker-free) | Flicker value: less than 2% for the whole dimming range |
| Start-up time | <1s (@230Vac) |
| No-load output voltage | 68VDC Max. |
| Load output voltage range | 9-58VDC |
| Full load output power | 25W Max. |
| Load output current | 350MA(9-58V)500MA(9-50V)550MA(9-45V)700MA(9-36V) |
| Constant current/voltage Precision | Constant Current Precision ±5% |
| Wiring method | Push terminal, wire cross section:0.75-1.0mm2 |
| Control Method | Primary PUSH Dimming | Primary PUSH dimming (Max.lead length:20M) |
| 1-10V Dimming | 1-10V dimming(Port current＜1MA) (Max.lead length:20M) |
| Dimming Range | Primary PUSH & DALI dimming: 0%-100%
1-10V dimming:2%-100% (Turn off below 1V) |
| Control Method | Primary PWM Dimming | 1-10V port PWM dimming (3KHZ-8KHZ) |
| Output auxiliary power port | 12±0.6V Port load capability:50mA |
| Sensor Dimming | Could be dimmable working with our sensor, match to PWM(3KHZ-8KHZ)or 1-10V.. |
| Wiring Method | Push Terminal, sensor port 3pin; |
| Potentiometer | Yes, 100kΩ |
| DALI Dimming | DALI dimming (Max.lead length:300M) |
| Exception Protection Requirements | Output over temperature
protection | Yes, without a self-recovery function(Can be inquired) |
| Output short circuit protection | Yes, without a self-recovery function(Can be inquired) |
| Operating Environment | Operating temperature/ humidity | -25℃~50℃ Humidity:85% (Non-condensing) |
| Storage temperature/ humidity | -40℃~80℃, Humidity:10%–95% |
| Max. case temp(Tc) | 85℃ |
| Safety & EMC | EMC standard | EN55015 EN61547 EN61000-3-2 EN61000-3-3 |
| DALI protocol standard | IEC62386-102 IEC62386-207 DT6 |
| Safety standard | EN61347-1 EN61347-2-13 |
| Certification | CE |
| Withstand voltage | 3750Vac, 5mA, 60s (Input “L N”- Output “SEC”) |
| Others | Degrees of protection | IP20 |
| Type of protection | Class II |
| Installation type | Independent installation |
| Installation dimension | 110*50*23.5mm |
| Blackout memory function | Yes, PUSH blackout memory |
| PUSH dimming synchronization | Parallel: 15 units Max. Series: 25 units Max. |
| Packaging requirement | white box+ Instructions Clapboard Outer Carton(K=A) |
| Weight | 140±5g |
| Life | 5 years guarantee @Ta full load |
| Note: All parameters are tested at the input voltage of 230VAC and a 25-degree environment unless specified. |
3. Dimension (Unit: mm):
4. Wring Diagram:
1) PUSH Dimming wiring diagram
2) DALI wiring diagram
3) 0-10V dimming wiring diagram
4) Sensor Dim
5. Derating
6. Dimming curve
7. Current gear setting
| Current / voltage gear setting | 1 | 2 |
| 350mA | ○ | ○ |
| 500mA | ● | ○ |
| 550mA | ○ | ● |
| 700mA | ● | ● |
8. ON/OFF & Description of Dimming Operation
A. Short-press the PUSH switch (short-press time 0.1s-1s), the LED driver will turn on or off.
B. Dimming:
Press and hold the PUSH switch (1s-8s), the LED driver can achieve dimming, brightening, or dimming, the dimming range is 2-100%.
C. Memory:
PUSH dimming has a dimming memory function.
D. Dimming synchronization:
The power connected to the same PUSH switch can be synchronized by pressing and holding the PUSH switch for longer than 15s
E. DALI dimming mode:
Connect the power supply to the DALI system, and it can be dimmed by the DALI host. The dimming range is 0-100%.
9. Matters needing Attention
1) The LED driver must be connected to the load before turning on the input power; otherwise, the LED driver may be damaged.
2) After the LED drive input is powered off, there will be a residual voltage at the output, which can be maintained for about 3 minutes.
Product Tags:
|
|
25W CC 350mA to 700mA PUSH and DALI2 compact led driver with 5 years warranty Images
|
